用于电弧检测的电力专用SoC设计

针对传统的电弧电路故障检测结果不准确的问题,设计用于电弧检测的SoC系统,并且在55nm工艺下进行流片验证。采用包含两种结构的模数转换器的片上电压源,设计了锁相环以及复位电路,精度最高可达8.67 bit。验证结果表明,本设计可提高电弧检测的准确性。     

Sizing of multi-stage Op Amps by combining design equations with the gm/ID method

Analog integrated circuit design has as integral parts both analytical reasoning and numerical validation in the process from topology construction to sizing. Given a circuit topology, different circuit sizing results can be obtained from different processes of sizing inference. Sizing methods by simulation-based numerical searching have been a continuously studied subject. However, almost all approaches in this category require an overwhelming number of circuit simulations to arrive at an optimized sizing result. On the other hand, many published manual sizing methods by using the conventional device equations also require repeated SPICE simulations to correct the equation-based sizing results. This paper proposes a systematic gm/ID-based initial sizing method specifically customized for designing multiple-stage operational amplifiers (Op Amps). A main feature of the proposal is to use circuit-level design equations as constraints on the gm/ID table lookup method to substantially reduce the uncertainty in the sizing calculations. As a result, a significant amount of SPICE based correction work can be reduced to complete an initial sizing. The proposed sizing procedure includes a few regular sizing rules customized to the configuration of multi-stage Op Amps. We validate the proposed sizing method by application to several multi-stage Op Amp examples with a capacitive load or Miller compensation. Simulations have justified that the produced initial sizing results can achieve most of the prespecified design targets.     

基于单片机C8051F500的无刷直流电机控制研究

永磁无刷直流电机是近些年发展起来的一种新型电机,具有效率高、调速性能好、启动转矩大等诸多优点,在运动控制领域中的应用日趋广泛。基于电机专用控制芯片MC33035,采用单片机C8051F500为主控芯片,设计一款无刷直流电机智能控制器,实现对无刷直流电机启动停止、正反转、调速、转速显示等控制。通过简要介绍无刷直流电机工作原理,使用MATLAB/Simulink对控制系统进行建模仿真,对无刷直流电机控制系统进行软、硬件设计。实验结果表明,该控制系统运行稳定,抗干扰性强,具有良好的市场应用价值。     

Modeling and design of 3-D MPPT for ultra low power RF energy harvesters

Radio-Frequency (RF) energy harvesting must cope with the limited availability and high variability of the energy source. In this paper, the modeling of an RF harvester for ultra low power environments is presented. A mathematical model based on theoretical analysis is developed. The model demonstrates that the maximum transferred power point is located in a three-dimensional space defined by the input capacitance, the output voltage, and the load resistance of the rectifier circuit. Moreover, the mathematical model returns results in substantial agreement with the SPICE simulation results, while guaranteeing a remarkable reduction of the required computation time. Furthermore, the paper reports the implementation of a mixed signal system for the 3-D MPPT, to be embedded in an RF harvester, in a 65 nm CMOS technology. The circuit exhibits a simulated power consumption lower than 100 nW, making this solution suitable for ultra low power harvesting.     

织物表面导电线路喷射打印起始端凸起形成过程研究

为提高织物表面微滴喷射打印导电线路的成形质量,针对导电线路喷射打印过程中线路沉积形貌的起始端凸起现象,利用高速相机对线路成形过程进行采集,研究微滴间融合振荡过程中左右接触角的动态变化,微滴与线路融合以及液体向线路起始端的输送过程,提出线路起始端凸起的消除方案并进行实验。结果表明:在融合振荡过程中,微滴向起始端的振荡趋势始终大于向另一侧的振荡趋势,导致打印线路起始端的织物基板润湿区域不断扩大;微滴与线路接触后,其中一部分液体润湿织物基板拓展线路长度,一部分通过线路以恒定速度输送至起始端,在线路起始端形成凸起;利用抗坏血酸溶液润湿织物表面后,成形线路起始端凸起现象得到消除,整体线路路径均匀,沉积形貌良好。     

一种新型回路电阻测试仪的研究与设计

针对传统低压回路电阻测试仪只能在被测设备停电时使用的一大限制,本文提出并设计了一种新型低压回路电阻测试仪。该仪器可在低压设备运行状态下对其回路电阻进行测量,在保证测量精度的前提下减少了设备停电率,大大提高了工作效率。     

Physics‐based model of lithium‐ion batteries running on a circuit simulator

The authors developed a physics‐based equivalent circuit model of a lithium‐ion battery (LIB) whose parameters are continually updated, reflecting the theoretical calculation results of the Butler‐Volmer equation, diffusion equations of the lithium‐ion and lithium, and Nernst equations of the liquid and solid phases. The developed model was applied to the charge/discharge simulations of an LIB, and the experimental and simulated results of constant current discharges and pulsed‐charge/discharge were found to be in excellent agreement. In particular, using the developed model, analyzing transient responses of the LIB derived from the transition of the electric double layer charging to the electrode reaction is possible. These results demonstrate that the electrochemical performance of an LIB can be calculated on a circuit simulator using the developed model.     

Techno-economic analysis of e-waste based chemical looping reformer as hydrogen generator with co-generation of metals,electricity and syngas

Chemical looping reforming (CLR) is an efficient technology to convert hydrocarbon fuels into CO₂ and H₂ using metal oxide based oxygen carriers. The novelty of the present study is to utilize electronic waste such as printed circuit board (PCB) to generate high quality syngas and metallic components for the CLR process. A portion of the syngas generated during e-waste pyrolysis is used with coal and polypropylene for effective combustion. A techno-economic analysis is performed for the production of hydrogen and electricity in the CLR method. The levelized costs for electricity (LCOE), hydrogen (LCOH), syngas (LCOS), and metal (LCOM) production using e-wastes are estimated as 92.28 $/MWh, 3.67 $/kg, 0.0034 $/kWh, and 24.32 $/ton, respectively. The LCOH is found to be the least of 2.90 $/kg under the co-feed conditions of PCB syngas-PP. The integration of the e-waste based CLR with a steam turbine system achieved a net efficiency of 50%.     

一种可控的自动扶梯电磁铁驱动电路板

扶梯制动系统是扶梯在出现紧急状况下确保乘客安全的重要设施。制动系统中的安全制动是在工作制动器无法在规定的时间内制停扶梯的一个措施,往往是在一些特别危险的场合下被触发,因此对于此制动器的控制显得尤为重要。本文提出了一种新型的自动扶梯制动器电磁铁驱动电路的设计,该设计用纯电子线路替代了传统的电气与电子组合形式,直接由自动扶梯单片机控制单元进行控制。     

QKD系统中基于EA电路的诱骗态实现

使用诱骗态量子秘钥方案可以解决因光子数分离攻击而导致的安全漏洞,保证了长距离量子通信的安全。本文介绍了量子通信的相关原理,通过对电吸收调制电路和激光器驱动电路的设计,精确控制产生了1550 nm波段的窄脉冲,经过内部调制成功制备诱骗态光脉冲,其强度约为信号态光脉冲的三分之一,因激光器的同一性而具有一致的光学特征从而避免了时频窃听,并具有强度可调的优点。